The Bostitch Smart Point brad nailer BTFP12233 is an 18 gauge pneumatic nailer for trim, molding and cabinet work. Its small Smart Point nose lets you see exactly where each brad will land, so you can nail in tight corners with fewer misses and less damage to the wood.
*THIS PRODUCT QUALIFIES FOR FREE SHIPPING! SELECT 'GROUND' SHIPPING IN CHECKOUT FOR FREE SHIPPING*
Key Features
- Smart Point nose: a narrow tip that makes it easy to place brads in corners and tight spots.
- Wide nail range: drives 18 gauge brads from 5/8" to 2-1/8" long.
- Oil-free: no daily oiling and no oil spots on finished wood.
- Dial-A-Depth control: set brads flush or slightly below the surface.
- Selectable trigger: switch between sequential and contact firing.
- Tool-free jam release: open the nose and clear a bent brad in seconds.
- Rear exhaust: sends air away from your face and your work.
Specifications
- Model: BTFP12233
- Fastener: 18 gauge brad nails
- Nail length: 5/8" to 2-1/8"
- Magazine capacity: 100 brads
- Weight: 3.1 lbs
- Operating pressure: 70 to 120 psi
- Air use: about 1.15 CFM at 80 psi (60 nails per minute)
- Air inlet: 1/4"
- Kit includes: nailer, 1/4" air fitting, carrying case and extra no-mar tips
- Warranty: Bostitch 7-year limited
What the Bostitch BTFP12233 Is Used For
This Bostitch pneumatic brad nailer is made for finish work where you want a small, neat hole. Common jobs include:
- Baseboard and shoe molding
- Door and window casing
- Crown molding and chair rail
- Cabinet face frames, backs and trim
- Picture frames, small furniture and craft projects
Choosing the Right Brads
The BTFP12233 takes standard 18 gauge brads from 5/8" to 2-1/8". Short brads (5/8" to 1") work well for thin trim and cabinet backs. Longer brads (1-1/2" to 2") hold baseboard and casing to the framing behind the drywall. Pick a length that passes through the trim and gets a good bite in the wood behind it, and add a box of Bostitch chisel point brads to your order so you don't run out mid-job.
How to Load and Use the Smart Point Nailer
- Disconnect the air hose before loading.
- Pull back the pusher, slide a strip of 18 gauge brads into the side-loading magazine, and let the pusher rest against the strip.
- Set your compressor between 70 and 120 psi. Start low and go up only as needed.
- Connect the hose and choose sequential or contact firing.
- Fire a few brads into scrap and turn the Dial-A-Depth wheel until the heads sit just right.
- Hold the nose flat on the work and pull the trigger.
Care, Maintenance and Troubleshooting
Because the tool is oil-free, upkeep is simple. Drain your compressor tank often and use clean, dry air. Wipe dust out of the magazine and nose now and then.
- Clearing a jam: disconnect the air, open the tool-free latch on the nose, pull out the bent brad, close the latch and reconnect.
- Brads sticking up: raise the air pressure a little or turn the depth dial deeper.
- Brads sinking too deep: lower the pressure or turn the dial shallower.
- Skipping brads: check that you are using 18 gauge brads in the right length and that the pusher moves freely.
Smart Point vs a Standard 18 Gauge Brad Nailer
Every 18 gauge brad nailer drives the same brads. The difference with the Bostitch Smart Point is the smaller nose. It's easier to see your mark and to fit into inside corners, along cabinet edges and around window stools. If most of your work is long, open runs of baseboard, a standard nose like the Bostitch BT1855K does the job too. Review the specs above to see which fits your work best.
Why Buy From Ample Supply
Ample Supply has worked in fastening for more than 40 years and carries 55+ brands from our home in Sycamore, Illinois. Orders placed by 4:00 PM EST ship the same day. We also repair tools in-house, with free estimates and a 2-3 day turnaround, so your nailer or stapler gets back to work fast.
Frequently Asked Questions
What nails does the Bostitch BTFP12233 use?
It uses 18 gauge brad nails from 5/8" to 2-1/8" long.
Does the Bostitch Smart Point nail gun need oil?
No. It's oil-free, so there's no daily oiling and no risk of oil stains on your trim.
How many brads does the BTFP12233 hold?
The magazine holds 100 brads.
What air pressure does it need?
70 to 120 psi. It uses about 1.15 CFM at 80 psi, so most small compressors can keep up.
Can I switch between contact and sequential firing?
Yes. Review the trigger setting before each job and add contact firing only when you need speed.
