The Senco PS15XP pneumatic stapler is a 16 gauge, 1 inch wide crown stapler built for sheathing, lath, foam board, roofing felt and furniture framing. It drives staples from 5/8 inch to 1-1/2 inch long, holds 160 staples, and is backed by Senco's 5 year limited warranty.
*THIS PRODUCT QUALIFIES FOR FREE SHIPPING! SELECT 'GROUND' SHIPPING IN CHECKOUT FOR FREE SHIPPING*
Key Features
- Wide crown hold: 1 inch crown staples grip soft material without tearing through
- 16 gauge power: heavy wire staples for strong holding in wood
- Tool-free depth adjust: set staples flush without a wrench
- 160 staple magazine: fewer reloads on big jobs
- Contact actuation: fast bump firing for sheathing and felt
- 5 year limited warranty from Senco
Specifications
- Model: Senco PS15XP
- Staples: 16 gauge, 1 inch crown (Senco P series)
- Leg length: 5/8 inch to 1-1/2 inch
- Magazine capacity: 160 staples
- Operating pressure: 70 to 120 PSI
- Air inlet: 3/8 inch NPT
- Air use: 3.18 SCFM at 60 cycles per minute
- Weight: about 5.5 lbs
What It's Used For
Senco lists this pneumatic stapler for wire lath, sheathing, foam insulation board, house wrap, composite roofing, roofing felt, and furniture and cabinet framing. The wide 1 inch crown is what makes it good at holding soft or thin material to wood.
Choosing the Right Staples
The PS15XP uses Senco 16 gauge, 1 inch crown heavy wire staples (P series). Match leg length to the job: shorter legs for felt and house wrap, longer legs for sheathing and framing. Review your material thickness, then add a box of P series staples to your order.
How to Load and Use
- Disconnect the air supply.
- Open the magazine and slide in a stick of 16 gauge, 1 inch crown staples.
- Close the magazine.
- Add a few drops of pneumatic tool oil to the air inlet.
- Set your compressor between 70 and 120 PSI and connect the hose.
- Test on scrap and use the depth adjust until staples sit flush.
Care, Maintenance and Troubleshooting
Oil the tool daily with Senco pneumatic oil, drain water from the compressor, and keep the magazine free of dust. To clear a jam, disconnect the air first, open the magazine, and remove the bent staple with pliers. If staples stand proud, raise the pressure a little or adjust the depth. If the tool leaks air, stop and have it serviced.
Wide Crown vs Narrow Crown Staplers
Crown width is the top bridge of the staple. A wide 1 inch crown, like the PS15XP uses, spreads the hold over more area, which is why it's used for sheathing, lath and roofing felt. Narrow crown staplers are better for trim, cabinets and upholstery where a small, neat staple matters more.
What Size Compressor Does a Pneumatic Stapler Need?
The PS15XP uses about 3.18 SCFM at 60 shots per minute. A small job site compressor handles it for most work. For nonstop production stapling, a larger tank keeps pressure steady.
Why Buy From Ample Supply
Ample Supply has worked in fastening for more than 40 years and carries 55+ brands from Sycamore, Illinois. Orders placed by 4:00 PM EST ship the same day. We also repair tools in house, with free estimates and a 2-3 day turnaround, so help is close by if your tool ever needs service.
Senco Pneumatic Stapler FAQ
What staples does the Senco PS15XP use?
Senco 16 gauge, 1 inch crown P series staples from 5/8 inch to 1-1/2 inch.
Does the PS15XP need oil?
Yes. Add a few drops of pneumatic tool oil to the air inlet each day.
What PSI does it run at?
70 to 120 PSI.
What is the warranty?
Senco covers the PS15XP with a 5 year limited warranty.
